Artex Asbestos Removal in Liverpool

Swirled, stippled or patterned ceilings from before 2000 may contain a small amount of asbestos. We test first, then help you decide whether to remove, cover or leave the coating, and plan the work safely.

Call 07777 659786

Get help with this

We only use your details to reply to this enquiry. Privacy policy

Textured coatings such as Artex were sometimes made with chrysotile (white) asbestos, so ceilings and walls finished before 2000 may contain it. The only way to know is to have a sample analysed by a UKAS-accredited laboratory. If it does contain asbestos, HSE guidance treats small-scale removal with steam or gel as non-licensed work, large-scale steam or gel removal as notifiable non-licensed work, and energetic methods such as abrasive blasting, or coatings on asbestos insulating board, as licensed work. We test, explain the options and arrange removal using the right method.

Does my Artex contain asbestos?

“Artex” has become a general name for any textured decorative coating: swirls, stipples, fan patterns, bark effects and the rest. Some of these products contained a small proportion of asbestos to strengthen the finish, and many homes had ceilings coated during the 1960s, 70s and 80s. Later coatings were made without asbestos, but they look the same. Age, the pattern and how hard the surface is cannot confirm it either way, which is why asbestos testing is always the first step.

Because ceilings were often re-coated or patched at different times, one sample may not speak for the whole house. A lounge done in the 1970s and a bedroom done in the 1990s can give different results, so we usually suggest one sample per distinct coating.

Is asbestos Artex dangerous?

The asbestos in textured coatings is bound into the material, and in good condition, left alone and painted over, it releases very little. The risk comes from disturbing it: sanding, scraping, drilling holes for downlights, chasing in cables, or knocking down a ceiling. These activities can release fibres into the room and spread dust through the house.

Do not sand, scrape, drill or steam a textured ceiling or wall unless you know it does not contain asbestos. If you have already started, stop, keep people and pets out of the room, close the door and do not sweep or vacuum the dust. Call us to arrange sampling and advice.

Your options for an asbestos textured ceiling

  • Leave it and manage itIf it is in good condition and you are not doing work that will disturb it, leaving it alone is often the safest option. Painting over it with a standard emulsion is generally fine.
  • Cover itOver-boarding with plasterboard or applying a skim over a sealed surface can give a smooth finish without removing the coating. Fixing boards through the coating needs care, and the coating stays in place, so it should be recorded for future work. Our page on asbestos encapsulation explains sealing as a management option.
  • Remove itRemoval using steam or gel to soften the coating and scrape it off wet keeps dust down. This is the right choice when the ceiling will be taken down, rewired extensively or opened up in a refurbishment.
  • Remove the whole ceilingWhere the ceiling is coming down anyway, the method depends on what the coating is applied to. If the backing board is itself asbestos insulating board, the work becomes licensed.

Which category of work is Artex removal?

Job Usual category under HSE guidance
Drilling a few holes, or small areas (about 1 m² or less) removed by steam or gel to allow another task Non-licensed work
Large-scale removal by steam or gel, such as whole ceilings or rooms Notifiable non-licensed work (NNLW)
Energetic methods such as abrasive blasting, or coatings on asbestos insulating board Licensed work

Removing whole ceilings in one or more rooms is usually notifiable. That means the work must be notified online before it starts, and those carrying it out must have medical examinations and keep health records. If the coating sits on insulating board, the job moves into licensed work, which is only ever carried out by an HSE-licensed contractor after a 14-day ASB5 notification. Our asbestos insulating board page explains why AIB is treated so differently. For the full picture of the middle category, see non-licensed and NNLW work.

How we plan Artex removal

  1. Questions and testing. We ask which rooms are affected, the approximate age of the coatings and what you want to do with the rooms, then arrange sampling.
  2. Options and quote. With results in hand, we explain whether to leave, cover or remove, the category of work and any notification needed, and give you a written quote.
  3. Preparing the room. The room is cleared or contents sheeted, floors and walls protected with polythene, the doorway sealed and the area isolated from the rest of the house.
  4. Controlled removal. The coating is softened with steam or gel and removed wet, to keep fibre release as low as reasonably practicable. Waste is bagged as it comes off.
  5. Clean and check. The room is cleaned with suitable vacuum equipment and wet wiping, and inspected before the protection comes down.
  6. Waste and paperwork. Double-bagged, labelled waste is taken by a registered carrier to a permitted site with a hazardous waste consignment note.

A single room of Artex usually takes a few days, depending on area, ceiling height and how stubborn the coating is. After removal, the ceiling is generally ready for a plasterer to skim.

Textured coatings in Liverpool homes

Textured ceilings turn up in almost every kind of pre-2000 home across Merseyside, but some patterns are familiar. Victorian and Edwardian terraces in Wavertree, many of them let to tenants, were often modernised in the 1970s and 80s with swirled ceilings to hide cracked lath and plaster. In Southport, large Victorian villas converted into flats may have textured finishes in hallways and stairwells as well as individual rooms. Post-war council-built homes in Huyton often had stippled ceilings applied as standard during later refurbishments. If you are planning to rewire, fit downlights or knock rooms together, speak to our Liverpool asbestos removal specialists first, because those jobs disturb ceilings more than people expect.

Planning a bigger renovation?

If the ceilings are only one part of a wider project, such as a full refurbishment, a loft conversion or a kitchen extension, a refurbishment and demolition survey of the area will look for other materials too: floor tiles, boards around boxed-in pipes, cement flues and panels behind fires. Finding them all before work starts avoids builders stopping halfway. Our asbestos in the home guide lists the places to think about. When you are ready, we can coordinate removal across the whole job as part of our asbestos help across Merseyside.

Textured ceiling you want gone?

Call 07777 659786 or leave your details. Tell us which rooms have the coating, roughly when it went up and what you are planning, and we will call you back to arrange testing and talk through the options.

Frequently asked questions

Can I skim over Artex that contains asbestos?

Skimming or over-boarding a textured ceiling in good condition is a common way to get a smooth finish without removing it. Preparation must not involve sanding or scraping the coating, and the asbestos stays in place, so it should be recorded for anyone doing future work. Ask us before you book a plasterer.

Can I paint over asbestos Artex?

Generally yes. Painting a textured coating in good condition with ordinary emulsion does not disturb it and can help seal the surface. Avoid sanding or scraping it first, and do not use abrasive preparation. If the coating is flaking or damaged, get it tested before decorating.

Is it safe to drill into an Artex ceiling to fit lights?

Not until you know whether it contains asbestos. HSE treats drilling through textured coatings as non-licensed work, which still needs trained workers and controls to keep dust down. Have the coating tested first; if it is positive, the work should be done by people trained for asbestos tasks.

How much asbestos is usually in Artex?

Textured coatings that contained asbestos generally had only a small proportion of chrysotile. That is part of why HSE treats small-scale steam or gel removal as non-licensed work. It is still a hazardous material, and large-scale removal is notifiable, so it should never be sanded or dry-scraped.

Do I have to tell a buyer about asbestos Artex?

Sellers are generally expected to answer property questionnaires truthfully, and a known test result is relevant information. Having a laboratory result, and evidence of any removal with a consignment note, usually makes the conversation easier. For your specific situation, take advice from your solicitor or conveyancer.

Will I need to move out while Artex is removed?

Not usually for a single room, because the work area is sealed off from the rest of the house. For several rooms, or where removal affects stairs and landings, staying elsewhere for part of the job can be more practical. We discuss this when we plan the work.

Call 07777 659786